- 49
- 696 733
DIYIT13
Australia
Приєднався 15 кві 2013
How to replace main fuel filter in a prado 150 series.
How to replace main fuel filter prado 150 series
Переглядів: 5 782
Відео
How to replace Prado front brake pads and discs
Переглядів 2,9 тис.2 роки тому
How to replace your front brakes. As with any Diy projects, the user atoms
Gear box and diff breathers on a 150 series Toyota vPrado
Переглядів 1,2 тис.2 роки тому
How to install gear box breathers. As with any DIY Project the user assume all the risk.
How to change power steeing fluid on a Prado
Переглядів 5 тис.2 роки тому
A quick video on changing power steering fluid on most cars car. As with any DIY projects, the user assumes the risk.
Camper trailer (camprite) Diesel heater install
Переглядів 9062 роки тому
How to install a diesel heater in a camper trailer. As with any DIY projects, the user assumes the risk.
Treg hitch trailer connection frustration gone
Переглядів 3,2 тис.2 роки тому
Awesome piece of gear we found to make connecting our camper to the car so much easier definitely worth getting. www.mchitch.com.au/product-page/adaptor-coupling-for-treg-and-trigg
How to install a winch in a bull bar
Переглядів 7 тис.2 роки тому
How to install winch into a EBC bull bar on a Toyota prado As with any DIY projects, the user assumes the risk
How to replace rear brake pads Toyota Prado
Переглядів 3,7 тис.2 роки тому
How to replace rear brake pads on a Toyota prado 150.
How to fit a hat saver in your 4wd
Переглядів 7 тис.3 роки тому
fitting a hat saver into a Prado 150 series
Prado K&N filter service pad type
Переглядів 2693 роки тому
How to service your k&n filter. As with any DIY projects, the user assumes the risk
Toyota Prado 1kd fte timing belt ,water pump, idler bearings.
Переглядів 12 тис.3 роки тому
How to replace timing belt and water pump on a Toyota Prado As with any DIY projects, the user assumes the risk
Prado under bonnet air compressor
Переглядів 3,8 тис.3 роки тому
How to fit a air compressor under bonnet Prado 150 As with any DIY projects, the user assumes the risk
How to replace Upper control arm bushers
Переглядів 1,9 тис.4 роки тому
How to replace Upper control arm bushers Prado 90 series . As with any DIY projects, the user assumes the risk
How To Clean your EGR valve Prado/ Hilux 1KD-fte
Переглядів 8 тис.4 роки тому
How To Clean your EGR valve Prado/ Hilux 1KD-fte
How to customise your Prado with Toyota techstream
Переглядів 4,3 тис.4 роки тому
How to customise your Prado with Toyota techstream
How to bleed your brakes on a Prado using techstream
Переглядів 14 тис.4 роки тому
How to bleed your brakes on a Prado using techstream
How to replace awning270 hinge/knuckle (fox wing/bat wing)
Переглядів 5635 років тому
How to replace awning270 hinge/knuckle (fox wing/bat wing)
How to replace a cv boot on a Prado
Переглядів 15 тис.5 років тому
How to replace a cv boot on a Prado
How to replace injectors on a 1KZTE TD
Переглядів 57 тис.5 років тому
How to replace injectors on a 1KZTE TD
How to replace Tail shaft uni joints prado
Переглядів 4,7 тис.6 років тому
How to replace Tail shaft uni joints prado
How to reset timing belt light warning light prado 1kzte
Переглядів 147 тис.6 років тому
How to reset timing belt light warning light prado 1kzte
what do I do if I don’t have a diagnostic port. Can anyone help me. 97’ 1kzt 4Runner for Central America.
Perfect 👍🏼 Thanks buddy.
kzj95W プラドのタイミングベルト交換後の、「T-BELT警告灯」のリセット方法が、よく判りません。メーター裏のネジを入れ替えたり、メーター器本体を外し、スピードメーター単体を分離させ、オドメーター上部のギヤの噛み合わせを外し、カム位置を合わせる。……とマニュアルにありますが、実際、コンビネーションメーターから、スピードメーターの分離手順など記載が無いので、動画にて説明頂けると嬉しいです。 デジタルじゃなく、アナログメータータイプです。
Dont forget to do the bearing in your air conditioner compressor too
Cheers mate very helpful 👍
Just saw your video thanks for that. A question about that small pipe you pointed it have to be disconnected or connected after service? Thanks
Budget on a new return line rail, b'cos it'll usually crap itself on at least one injector regardless of how careful you go. You'll go to remove the nut on top of it, the return line boss will be seized to it & it'll twist. That shags the little steel pipes & renders the whole return line scrap. Use a proper injector socket to get the injectors out - makes life easy. While you're in there, whip out the glow plugs - takes seconds, you'll usually find one or 2 have shat the bed. Only way I have found to not ruin the return line is to first tighten the nuts holding it down with an impact wrench - that often (but not always) shocks the "bond" free & you can then remove the nut. However that doesn't always work - was doing a set today & the return line array mangled into a hoop - no biggie as you can buy a new one, but might be a biggie if you're doing this on a sunday, planning to drive to work on monday..
this is the best video for this task that exists, thanks so much. i'm on day 4 of this :o lol
Thanks for the thorough video! I'm planning to do injectors on my '98 Surf in a few weeks. No need to code the new injectors to the ECU?
Great video thanks for making it by any chance do you no what the torc nm is on the bolts on the Warter pump and the 4 fan bolts I'd appreciate it if you can help 👍
Thanks for your video do you know by any chance the torc speck on them 10mil bolts on the thumostat please and is it possible do you think to change it without taking off the ac and olternator off I'd appreciate your advice kind regards. Nick
mine is exactly the same !!!
Get ya mum to hold the camera/phone next time perhaps.. A for effort though!
I can not find this adaptor any where :(
simple practical explanations of what you are required to do....
Good instruction from start to finish and one video. Not like someone else on UA-cam who wants you to watch a hundred videos with bits of information mixed in incoherently.
Thanks BRO!!!
Thanks mate, aussie legend 👍
Hi mate did you need to code new injectors?
I change my fuel filter at every oil change, but might be looking at doing it every 10,000ks if i use a Ryco or Terrain Tamer brand.
Hi mate, how many km where on those glow plugs when you replaced them?
About 300 thousand kms.
Where any of the tips cracked off? Did you have any trouble getting them out of the head? Little concerned to do mine they where replace 240,000km ago in 2015. (Edit) got them done yesterday with no problems thank God. The person that replaced them in 2015 used anti seized and the tips where all still on them. Good luck to those looking to do this job. This is probably the one of the best videos out there on how to do it on a kzj95.
Thanks for the great demo. Gonna give it a go.
my 1kz-te just won't start. after having hard start issues. any ideas?
My trip and odom is an analog how do you reset
legend!!
Awesome video! Ty
Cheers mate 👍
Hello mate, is there any way to open and clean the fuel solenoids. Where I am from difficult to get fuel solenoids.
I’ve got todo the front seal on mine. Is it the same process?
Yeah pretty much. You will have to remove the front shaft completely to be able to get the flange bolt.
@@DIYIT13 appreciate the response, going to be doing mine this week. Seems like a straightforward procedure. Ok to re use the nut? Just hoping I have the right size socket. My rattle gun should be able to zip it off
did you ever solve the code 14?
Thanks for the video 😊
Is the front seal the same procedure? (great concise video - no waffle like many !)
Cheers mate, Yes the only difference is you would have to drain the oil first. D
Good idea l like the idea thanks
Awesome video, very informative. - love your watch - care to share what it is?
Hey mate, do you find these ate slippery withwet shoes?
Heya , Honestly I haven't even given it a thought. So if they are slippery it hasn't bothered me. Cheers, D
Life saver man
Hey mate how did you get the clip off?
Where you showed us before you took the boot off
You use circlip pliers.
You will need a wheel alignment after this….any steering or front suspension component loosened off and/or replaced to gain access to another one = wheel alignment
Great video mate. Thank you. I like your crank seal removal method, very clever. 👏
Glad it helped
Затяжка форсунок 54 n/m Затяжка обратки 20n/m
Купил на АлиЭкспресс форсунки в сборе. Цена за 4 шт 100-200$ USA. Самый лучший выход. Ещё нужно проверить датчик положения дроссельной заслонки и датчик MAF. Из-за них тоже будет большой расход топлива. Свечи накала на расход топлива не влияют. Они улучшают запуск двигателя и работу в холодное время года. В Австралии двигатель запускается даже если все свечи будут отключены
Thank you!
You're welcome!
Can you tell me size of the bearings on idle pulleys and tensioner pulley?
Sorry no , I purchased a kit with them all in it. D
Great, but what types, sockets and coloures do you need to buy if you want to change all bulbs? And can you buy it from ebay?
Thanks for the video. 2years down the track has there been any issues with the modified bracket ?
Solid explanation with good tips! Cheers bro
Appreciate it!
It is Toyota 80???
no this is PRADO 90 series
boost gauge????
Hi mate, I'm guessing you downloaded Techstream from the net on this computer? Do you have any tutorials on this? Cheers.
My car Toyota land sub tank is not working